technical data sheet 6 lake street, lawrence, ma 01841 gort road business park, ennis, co. clare, ireland 1-800-446-1158 / (978) 620-2600 / fax: (978) 689-0803 tel: +353 (0) 65 6840044 fax: +353 (0) 65 6822298 website: http://www.microsemi.com n-channel logic level mosfet qualified per mil-prf-19500/570 t4-lds-0188 rev. 1 (101985) page 1 of 3 devices levels 2N6901 jan jantx jantxv absolute maximum ratings (t c = +25c unless otherwise noted) parameters / test conditions symbol value unit drain ? source voltage v ds 100 vdc gate ? source voltage v gs 10 vdc continuous drain current t c = +25c i d1 1.69 adc continuous drain current t c = +100c i d2 1.07 adc max. power dissipation p tl 8.33 (1) w drain to source on state resistance r ds(on) 1.4 (2) operating & storage temperature t op , t stg -55 to +150 c note: (1) derated linearly by 0.067 w/c for t c > +25c (2) v gs = 5vdc, i d = 1.07a electrical characteristics (t a = +25c, unless otherwise noted) parameters / test conditions symbol min. max. unit off charactertics drain-source breakdown voltage v gs = 0v, i d = -1madc v (br)dss 100 vdc gate-source voltage (threshold) v ds v gs , i d = 1.0ma v ds v gs , i d = 1.0ma, t j = +125c v ds v gs , i d = 1.0ma, t j = -55c v gs(th)1 v gs(th)2 v gs ( th ) 3 1.0 0.5 2.0 3.0 vdc gate current v gs = 10v, v ds = 0v v gs = 10v, v ds = 0v, t j = +125c i gss1 i gss2 100 200 nadc drain current v gs = 0v, v ds = 80v v gs = 0v, v ds = 80v, t j = +125c i dss1 i dss2 1.0 50.0 adc uadc static drain-source on -state resistance v gs = 5v, i d = 1.07a pulsed t j = -125c v gs = 5v, i d = 1.07a pulsed r ds(on)1 r ds(on)2 1.4 2.6 diode forward voltage v gs = 0v, i d = 1.69a pulsed v sd 0.8 1.6 vdc 2N6901 to-205af (formerly to-39) see figure 1
technical data sheet 6 lake street, lawrence, ma 01841 gort road business park, ennis, co. clare, ireland 1-800-446-1158 / (978) 620-2600 / fax: (978) 689-0803 tel: +353 (0) 65 6840044 fax: +353 (0) 65 6822298 website: http://www.microsemi.com t4-lds-0188 rev. 1 (101985) page 2 of 3 dynamic characteristics parameters / test conditions symbol min. max. unit gate charge: q g(on) q gs q gd nc on-state gate charge gate to source charge gate to drain charge v gs = 5v, i d = 1.69a v ds = 50v 5.0 1.0 2.9 switching characteristics parameters / test conditions symbol min. max. unit switching time tests: turn-on delay time rinse time turn-off delay time fall time i d = 1.69a, v gs = 5vdc, gate drive impedance = 25 , v dd = 50vdc t d(on) t r t d(off) t f 25 80 45 80 ns diode reverse recovery time di/dt 100a/s, v dd 30v, i f = 1.0a t rr 250 ns
technical data sheet 6 lake street, lawrence, ma 01841 gort road business park, ennis, co. clare, ireland 1-800-446-1158 / (978) 620-2600 / fax: (978) 689-0803 tel: +353 (0) 65 6840044 fax: +353 (0) 65 6822298 website: http://www.microsemi.com t4-lds-0188 rev. 1 (101985) page 3 of 3 package dimensions note: 1. dimensions are in inches. 2. millimeters are given for general information only. 3. beyond radius(r) maximum, tw shall be held for a minimum length of .011 (0.28 mm). 4. dimension tl measured from maximum hd. 5. outline in this zone is not controlled. 6. dimension cd shall not vary more than .010 (0.25 mm) in zone p. this zone is controlled for automatic handling. 7. leads at gauge plane .054 +.001, -.000 (1.37 +0.03, -0.00 mm) below seating plane shall be within .007 (0.18 mm) radius of true position (tp) at maximum material condition (mmc) relative to tab at mmc. 8. lu applies between l1 and l2. ld applies between l2 and ll minimum. diameter is uncontrolled in l1 and beyond ll minimum. 9. all three leads. 10. radius(r) applies to both inside corners of tab. 11. drain is electrically connected to the case. 12. pin out: 1- source, 2 - gate, 3 - drain (case). 13. in accordance with asme y14.5m , diameters are equivalent to x symbology. figure 1. physical dimensions for to-205 af dimensions symbol inches millimeters min max min max cd .305 .335 7.75 8.51 ch .160 .180 4.07 4.57 hd .335 .370 8.51 9.40 lc .200 tp 5.08 tp ld .016 .021 0.41 0.53 8,9 ll .500 .750 12.70 19.05 8,9 lu .016 .019 0.41 0.48 8,9 l1 .050 1.27 8,9 l2 .250 6.35 8,9 p .100 2.54 6 q .050 1.27 5 tl .029 .045 0.74 1.14 4 tw .028 .034 0.71 0.86 3 r .010 0.25 10 45 tp 45 tp 6
|
